Questions about the category: IP Connectivity

Interpret the components of routing table. Determine how a router makes a forwarding decision by default. Configure and verify IPv4 and IPv6 static routing. Configure and verify single area OSPFv2. Describe the purpose, functions, and concepts of first hop redundancy protocols

30 questions were found
Displaying questions 1 to 30.

Which two options are the best reasons to use an IPV4 private IP space

CCNA 200-301

Cisco

Which two options are the best reasons to use an IPV4 private IP space? (Choose two.)

Refer to the exhibit. When PC1 sends a packet to PC2, the packet has

CCNA 200-301

Cisco

Refer to the exhibit. When PC1 sends a packet to PC2, the packet has which source and destination IP address when it arrives at interface Gi0/0 on router R2?
Questão 2 CCNA 200-301

Shortly after SiteA was connected to SiteB over a new single-mode

CCNA 200-301

Cisco

Questão CCNA 200-301
Refer to the exhibit. Shortly after SiteA was connected to SiteB over a new single-mode fiber path, users at SiteA report intermittent connectivity issues with applications hosted at SiteB.

Which type of route does R1 use to reach host 10.10.13.10/32?

CCNA 200-301

Cisco

Question CCNA 200-301

Which prefix does Router1 use for traffic to Host A?

CCNA 200-301

Cisco


Question CCNA 200-301

Which command automatically generates an IPv6 address from a specified

CCNA 200-301

Cisco

Which command automatically generates an IPv6 address from a specified IPv6 prefix and MAC address of an interface?

When configuring IPv6 on an interface, which two IPv6 multicast groups

CCNA 200-301

Cisco

When configuring IPv6 on an interface, which two IPv6 multicast groups are joined? (Choose two)

An engineer must configure a /30 subnet between two routes...

CCNA 200-301

Cisco

An engineer must configure a /30 subnet between two routes.

Which network allows devices to communicate without the need to

CCNA 200-301

Cisco

Which network allows devices to communicate without the need to access the Internet?

Refer to the exhibit. Which statement explains the configuration error

CCNA 200-301

Cisco

Question CCNA 200-301

Which IPv6 address type provides communication between subnets and

CCNA 200-301

Cisco

Which IPv6 address type provides communication between subnets and cannot route on the Internet?

Which IPv6 address block sends packets to a group address rather than

CCNA 200-301

Cisco

Which IPv6 address block sends packets to a group address rather than a single address?

Which function does the range of private IPv4 addresses perform?

CCNA 200-301

Cisco

Which function does the range of private IPv4 addresses perform?

Which action must be taken to assign a global unicast IPv6 address on

CCNA 200-301

Cisco

Which action must be taken to assign a global unicast IPv6 address on an interface that is derived from the MAC address of that interface?

Several new coverage cells are required to improve the Wi-Fi network

CCNA 200-301

Cisco

Several new coverage cells are required to improve the Wi-Fi network of an organization. Which two standard designs are recommended? (Choose two.)

Which IPv6 address block forwards packets to a multicast address

CCNA 200-301

Cisco

Which IPv6 address block forwards packets to a multicast address rather than a unicast address?

Which type of IPv6 address is publicly routable in the same way as

CCNA 200-301

Cisco

Which type of IPv6 address is publicly routable in the same way as IPv4 public addresses?

What is the expected outcome when an EUI-64 address is generated?

CCNA 200-301

Cisco

What is the expected outcome when an EUI-64 address is generated?

Which subnet summarizes and gives the most efficient distribution of

CCNA 200-301

Cisco

A corporate office uses four floors in a building.
✑ Floor 1 has 24 users.
✑ Floor 2 has 29 users.
Floor 3 has 28 users.

✑ Floor 4 has 22 users.

Which IPv4 network and subnet mask combination does the engineer

CCNA 200-301

Cisco

Question CCNA 200-301
Refer to the exhibit. An engineer must add a subnet for a new office that will add 20 users to the network.

An office has 8 floors with approximately 30-40 users per floor

CCNA 200-301

Cisco

An office has 8 floors with approximately 30-40 users per floor.

Which technique can you use to route IPv6 traffic over an IPv4

CCNA 200-301

Cisco

Which two statements are true about the command ip route 172.16.3.0 25

CCNA 200-301

Cisco

Which two statements are true about the command ip route 172.16.3.0 255.255.255.0 192.168.2.4?

Which two goals reasons to implement private IPv4 addressing on your

CCNA 200-301

Cisco

Which two goals reasons to implement private IPv4 addressing on your network?

What is the binary pattern of unique ipv6 unique local address?

CCNA 200-301

Cisco

What is the binary pattern of unique ipv6 unique local address?

A network engineer must configure the router R1 GigabitEthernet1/1

CCNA 200-301

Cisco

A network engineer must configure the router R1 GigabitEthernet1/1 interface to connect to the router R2 GigabitEthernet1/1 interface. For the configuration to be applied, the engineer must compress the address 2001:0db8:0000:0000:0500:000a:400F:583B.

In which situation is private IPv4 addressing appropriate for a new

CCNA 200-301

Cisco

In which situation is private IPv4 addressing appropriate for a new subnet on the network of an organization?

Why was the RFC 1918 address space defined?

CCNA 200-301

Cisco

A network administrator is setting up a new IPv6 network using the

CCNA 200-301

Cisco

A network administrator is setting up a new IPv6 network using the 64-bit address 2001:0EB8:00C1:2200:0001:0000:0000:0331/64. To simplify the configuration, the administrator has decided to compress the address.

What is an appropriate use for private IPv4 addressing?

CCNA 200-301

Cisco

Cookies Consent

We use cookies to enhance your browsing experience, serve personalized ads or content, and analyze our traffic. By clicking "Accept All" you consent to our use of cookies. Privacy Policy.