Questions about the category: Network Access

Configure and verify VLANs (normal range) spanning multiple switches. Configure and verify interswitch connectivity. Configure and verify Layer 2 discovery protocols (Cisco Discovery Protocol and LLDP). Configure and verify (Layer 2/Layer 3) EtherChannel (LACP). Describe the need for and basic operations of Rapid PVST+ Spanning Tree Protocol and identify basic operations. Compare Cisco Wireless Architectures and AP modes. Describe physical infrastructure connections of WLAN components (AP,WLC, access/trunk ports, and LAG). Describe AP and WLC management access connections (Telnet, SSH, HTTP,HTTPS, console, and TACACS+/RADIUS).

26 questions were found
Displaying questions 1 to 26.

What is the same for both copper and fiber interfaces when using SFP

CCNA 200-301

Cisco

What is the same for both copper and fiber interfaces when using SFP modules?

What is a recommended approach to avoid co-channel congestion while

CCNA 200-301

Cisco

What is a recommended approach to avoid co-channel congestion while installing access points that use the 2.4 GHz frequency?

An engineer observes high usage on the 2.4GHz channels and lower usage

CCNA 200-301

Cisco

An engineer observes high usage on the 2.4GHz channels and lower usage on the 5GHz channels. What must be configured to allow clients to preferentially use 5GHz access points?

A frame that enters a switch fails the Frame Check Sequence. Which two

CCNA 200-301

Cisco

A frame that enters a switch fails the Frame Check Sequence.

Which 802.11 frame type is Association Response?

CCNA 200-301

Cisco

Which 802.11 frame type is Association Response?

In which way does a spine-and-leaf architecture allow for scalability

CCNA 200-301

Cisco

In which way does a spine-and-leaf architecture allow for scalability in a network when additional access ports are required?

What is the default behavior of a Layer 2 switch when a frame with an

CCNA 200-301

Cisco

What is the default behavior of a Layer 2 switch when a frame with an unknown destination MAC address is received?

What is a benefit of using a Cisco Wireless LAN Controller?

CCNA 200-301

Cisco

What is a benefit of using a Cisco Wireless LAN Controller?

Which action is taken by switch port enabled for PoE power

CCNA 200-301

Cisco

Which action is taken by switch port enabled for PoE power classification override?

What occurs to frames during the process of frame flooding?

CCNA 200-301

Cisco

What occurs to frames during the process of frame flooding?

What are two differences between optical-fiber cabling and copper

CCNA 200-301

Cisco

What are two differences between optical-fiber cabling and copper cabling? (Choose two)

How does CAPWAP communicate between an access point in local mode and

CCNA 200-301

Cisco

How does CAPWAP communicate between an access point in local mode and a WLC?

A wireless administrator has configured a WLAN; however, the clients

CCNA 200-301

Cisco

A wireless administrator has configured a WLAN; however, the clients need access to a less congested 5-GHz network for their voice quality.

For what two purposes does the Ethernet protocol use physical

CCNA 200-301

Cisco

You are configuring your edge routers interface with a public IP

CCNA 200-301

Cisco

You are configuring your edge routers interface with a public IP address for Internet connectivity. The router needs to obtain the IP address from the service provider dynamically.

Refer to the exhibit. A network technician is asked to design a small

CCNA 200-301

Cisco

Refer to the exhibit. A network technician is asked to design a small network with redundancy. The exhibit represents this design, with all hosts configured in the same VLAN.

Question CCNA 200-301

Which WAN access technology is preferred for a small office / home

CCNA 200-301

Cisco

Which WAN access technology is preferred for a small office / home office architecture?

What is a role of access points in an enterprise network?

CCNA 200-301

Cisco

What is a role of access points in an enterprise network?

How does a Cisco Unified Wireless Network respond to Wi-Fi channel

CCNA 200-301

Cisco

How does a Cisco Unified Wireless Network respond to Wi-Fi channel overlap?

Which 802.11 frame type is indicated by a probe response after a

CCNA 200-301

Cisco

Which 802.11 frame type is indicated by a probe response after a client sends a probe request?

Which function forwards frames to ports that have a matching

CCNA 200-301

Cisco

Which function forwards frames to ports that have a matching destination MAC address?

What provides centralized control of authentication and roaming in an

CCNA 200-301

Cisco

What provides centralized control of authentication and roaming in an enterprise network?

Which set of 2 4 GHz nonoverlapping wireless channels is standard in

CCNA 200-301

Cisco

Which set of 2 4 GHz nonoverlapping wireless channels is standard in the United States?

What is a requirement for nonoverlapping Wi-Fi channels?

CCNA 200-301

Cisco

What is a requirement for nonoverlapping Wi-Fi channels?

What are the two functions of SSIDs? (Choose two)

CCNA 200-301

Cisco

What are the two functions of SSIDs?

Which PoE mode enables powered-devices detection and guarantees power

CCNA 200-301

Cisco

Which PoE mode enables powered-devices detection and guarantees power when the device detected?

Support us!
Subscribe Now

Cookies Consent

We use cookies to enhance your browsing experience, serve personalized ads or content, and analyze our traffic. By clicking "Accept All" you consent to our use of cookies. Privacy Policy.